![curtains windows with small windows on top curtains windows with small windows on top](https://i5.walmartimages.com/asr/8c811405-fba0-4ec2-9c18-ef9b58df5f37_1.ec9c345f63c37f765a2fb0942e2d4b90.jpeg)
We recommend a minimum of 4 inches above. You can achieve that by mounting your rod 8 to 10 inches above your window or for a more dramatic effect, 2 – 3 inches below your ceiling line or just below your crown molding or trim. If you are using tab / tie top drapery panels or clip rings which will lower your drapery making it sit well below the rod, you will need to move the rod up a few inches as an allowance for the difference, thus ensuring the top of your window will not be visible through the ‘gap’ created by the tab / tie top panels or the clip rings.ĭraperies can also help create the illusion of a taller / higher ceiling. You will want to hang the drapery high enough so it covers the top of the window by at least a few inches if possible.
![curtains windows with small windows on top curtains windows with small windows on top](https://media-cldnry.s-nbcnews.com/image/upload/newscms/2021_11/3456982/210315-blackout-curtains-bd-2x1.jpg)
Use a pencil to make a small mark on the wall on each side of the window, at the correct height. Measure on each side of your window to ensure that the window hardware is straight. Measure the height of your window treatments from the desired point (floor, window sill, etc.) Determining the appropriate height to hang your curtain rod is crucial to achieving a successful drapery installation. If space is tight, you can always opt for an end cap. Finials come in a wide range of sizes, from 1.5 inches to 9. Be sure to consider the extra space required for decorative finials as the rod dimensions will not include the additional width added by each finial. You may want to use a level to make sure the marks are straight.Īccounting for Finials. Using a pencil, make a small mark at the appropriate width on the wall. If the drapery fabric is unusually bulky, you may need to add an extra inch or two. Heavier fabrics and wider windows require more of a stack-back than lighter-weight fabrics on narrow windows.Ī good rule of thumb is to have the curtain rod extend three to four inches from each side of the window frame. It is not necessary for your drapery to always clear the window glass however, we recommend allowing at least 3 inches minimum on each side to allow the curtains to open completely! Let the sunlight through!įor most drapery, you should allow approximately one-third of the width of the window for the stack-back. This would result in all 48 inches of window glass showing when curtains are fully opened. To accomplish that, you would need to make sure the curtain rod is at least 20 inches larger than the original window size of 48 inches, or 68 inches. Ideally, you will want to have the stack pushed all the way over so that very little, if any, of the window glass is covered.
#Curtains windows with small windows on top full#
In other words, a full 20 inches (or ~40%) of the 48 inches of window glass will be covered by the stack. If the stack width of your chosen curtains is 10 inches on either side, it would result in 10 inches of window glass on either side being covered by the gathered drapery. This is important, especially when dealing with small windows as you will want to expose as much of the window glass as possible to give an illusion of a larger window.Īs an example, if your window is 48 inches (4 feet) wide and your curtains split in the middle.
![curtains windows with small windows on top curtains windows with small windows on top](https://hips.hearstapps.com/hmg-prod.s3.amazonaws.com/images/best-blackout-curtains-1580855681.png)
When your curtains are opened, they will gather on either end – this is what is referred to as the “stack or stack back”. The factor to consider when measuring the width is space needed for the stack. Here is a table to keep handy for determining rod lengths quickly: When measuring for window widths, you are trying to derive the right curtain rod length while considering how much you would like your curtains to carry on past the window opening.įor determining appropriate rod length, general industry rule of thumb is to add ~20% to the measured frame or casing width. Other things to keep in mind are a bit subjective and here are general guidelines for you to work with: Always double, triple check your measurements! You don't want to end up in the same position as this little fella.Record all measurements to the nearest 1/16th of an inch.Other types such as cloth can give erroneous measures